Yes, a gas conversion in Los Angeles needs a permit. The California Building Code requires you to obtain one before converting a gas system it regulates, and the permit comes from the City of Los Angeles or from LA County, depending on where your property sits. The permit is followed by an inspection, and SoCalGas will not turn on natural gas service until that inspection clears. This guide explains who issues the permit, what the fees look like, who may do the work and what happens at each step, so you can plan a conversion without surprises.
TL;DR
- A permit is required before you convert a gas system, whether you are switching a home from propane (LP) to natural gas or adding gas piping. Minor part replacements that do not change the equipment’s approval are exempt.
- Inside the City of Los Angeles, the Department of Building and Safety (LADBS) issues the permit. In unincorporated LA County, Public Works Building and Safety does.
- LA County’s 2026-2027 fee schedule lists a $41.35 base plumbing permit plus $24.47 for a low-pressure gas system of five outlets or fewer.
- SoCalGas will not establish natural gas service until local inspectors release the piping and its own safety requirements are met.
- Gas conversion is licensed work. Book a licensed technician before you start, not after.
Table of Contents
- Does a gas conversion need a permit in Los Angeles?
- Which agency issues your permit?
- What does the permit application need?
- What does the permit cost?
- Who is allowed to do the work?
- The step-by-step process
- Common mistakes that delay conversions
- Our perspective on gas conversions
- Book a licensed technician for your conversion
- FAQ
- Sources
Does a gas conversion need a permit in Los Angeles?
It does. Section 105.1 of the 2025 California Building Code says an owner or authorized agent must apply for and obtain a permit before converting or replacing a gas system the code regulates. Section 105.2 lists the exemptions: portable heating appliances, and replacing minor parts that do not change the equipment’s approval or make it unsafe. A full LP to natural gas conversion is not a minor part swap, so assume a permit applies.
LA County’s plumbing code is even more direct. Title 28, Section 103.1 makes it unlawful to install, alter or repair any gas piping without first getting a permit from the authority having jurisdiction. The only stated exception is the gas supplier disconnecting defective piping or equipment.
Two plain-language points help here:
- A permit is a request for inspection. The City of Los Angeles municipal code says a permit is merely an application for inspection, and that issuing it is not approval of the work. The inspection is where the work is actually checked.
- It protects you later. LADBS describes permitting as both a safety and a financial-protection step: it is required by law and creates the paper trail you need when you sell or refinance. An unpermitted gas conversion is the kind of thing that can surface at closing.
Which agency issues your permit?
Your address decides, not your mailing city. Many addresses that say “Los Angeles” are in the city, but others sit in unincorporated county areas or in separate cities with their own building departments.
| Where the property is | Who issues the permit | How to apply |
|---|---|---|
| City of Los Angeles | LADBS | Simple projects through PermitLA, projects needing plan check through ePlanLA |
| Unincorporated LA County | LA County Public Works Building and Safety | Through the county permit process |
| Another incorporated city (for example, Long Beach or Pasadena) | That city’s building department | Check the city’s own site |
LADBS states that simple projects on its Express Permit list need no plan review and can be applied for directly in the PermitLA web app. Everything else, including projects that need plan check, goes through ePlanLA. Both require a free Angeleno account, and in-person visits to a Development Services Center need an appointment. LADBS also notes that homeowners applying for single-family e-permits can apply for building, mechanical, electrical and plumbing permits.
In unincorporated areas, LA County Public Works says a permit can only be issued to a contractor with the appropriate CSLB license, to the owner in certain cases, or to an authorized agent. The permit holder must request an inspection within 12 months of issuance, and follow-up inspections are needed every 180 days. Permit issuance can also depend on approvals from other agencies when the scope of work triggers them.
Orange County homeowners should note that the rules above are Los Angeles specific. Properties in Orange County cities answer to their own city building departments, though the state code and SoCalGas process are the same.
What does the permit application need?
The city code requires applications on department forms, with the information needed to enforce the building code and the California Energy Code. Plans or a diagram are required when the code calls for them, and the permit issues once fees are paid. Section 93.0204 was amended by Ordinance 188,739, effective September 23, 2025, so use LADBS’s current forms rather than an older checklist.
For a conversion, expect to have these ready:
- The address and whether the property is in the city, the county or another city.
- A list of the gas appliances being converted or connected, with model information.
- The connected load, in BTU per hour, for each appliance.
- A simple piping diagram if the scope includes new or altered gas lines.
- The licensed contractor’s details, or the owner’s details where owner permits are allowed.
Why BTU load matters
BTU per hour is how much fuel an appliance can burn. The gas company and the inspector use it to confirm the meter and the pipe can supply everything at once. SoCalGas’s service guidebook lists typical connected loads:
| Appliance | Typical load (BTU/hr) |
|---|---|
| Stand-alone oven | 30,000 to 50,000 |
| Conventional tank water heater | 30,000 to 100,000 |
| Tankless water heater | 120,000 to 199,000 |
| Conventional furnace | 80,000 to 120,000 |
| Clothes dryer | 30,000 to 50,000 |
| Natural gas grill | 20,000 to 60,000 |
These are typical ranges. Your appliance’s data plate gives the real figure. A tankless water heater is the one that most often changes the math, because its load can exceed a whole kitchen’s worth of other appliances.
Which appliances can be converted
Not every appliance can run on natural gas. For propane and electric to natural gas projects, SoCalGas instructs that the service application should list only appliances that are convertible, and that homeowners can schedule an appliance inspection through the SoCalGas Customer Contact Center (residential line 1-877-238-0092) to make that determination. Many ranges, dryers and furnaces ship with or accept a conversion kit, but the manufacturer’s label is what counts. If you are moving a gas dryer to a new home, this guide to preparing a gas dryer for a move covers the appliance-side checks that decide whether it can be reconnected safely.
For the technical side of the change itself, such as orifices and regulator settings, see our guide to gas orifice sizing for natural gas and propane.
What does the permit cost?
For unincorporated LA County, the plumbing fee schedule is public. The 2026-2027 County plumbing fee schedule, effective July 1, 2026, lists:
- Base plumbing permit: $41.35
- Low-pressure gas system, five outlets or fewer: $24.47, plus $6.20 for each additional outlet
- Medium- or high-pressure gas system: $100.62 each
- Gas pressure regulator, other than appliance regulators: $24.47 each
So a simple low-pressure gas job with five outlets or fewer comes to $65.82 in county permit fees ($41.35 plus $24.47). The county revises these amounts each July 1, and the schedule for the prior year, effective July 1, 2025, listed a $39.99 base and $23.66 for the same gas system. That year’s schedule also applied a plan-check fee of 40% of the required plumbing permit fee when plans needed plumbing-code plan check.
These are permit fees only. They do not include the contractor’s labor, parts, conversion kits, new gas line, or any City of Los Angeles fees, which LADBS sets on its own schedule. For realistic project budgets, our breakdown of Los Angeles gas line costs, permits and timeline shows how the pieces add up.
Who is allowed to do the work?
Gas piping and appliance conversion is licensed trade work in California. County Public Works limits who can hold a permit, as described above, and the person doing gas work needs the right California Contractors State License Board (CSLB) license. A general handyman does not qualify, and neither does an unrelated trade. Owner-builder exceptions exist in limited cases, but they still require permits and inspections, and they put the safety responsibility on you.
The practical reasons to hire a licensed technician are straightforward:
- A conversion changes how fuel burns. A wrong orifice or regulator setting can cause poor combustion, soot or carbon monoxide.
- The inspector looks for correct piping, sizing, shutoff valves and leak-tight joints.
- SoCalGas will not light the system until paperwork and inspection are in order.
If you own rental property, the same rules apply. The person who authorizes the work and holds responsibility for the building is the owner or property manager, so tenants cannot authorize a conversion on their own.
The step-by-step process
1. Confirm the jurisdiction and the scope
Look up whether your address is in the City of Los Angeles, unincorporated county or another city. Then list what is changing: one appliance conversion, a new gas line, a meter change, or a whole-house switch from propane to natural gas. A bigger scope means more permit items and more likely plan check.
2. Check that the appliances can convert
Read each data plate and the manufacturer’s manual. Appliances that cannot be converted are replaced, not modified. SoCalGas can inspect appliances to confirm what is convertible before service is applied for.
3. Apply for the gas service
SoCalGas needs an application that identifies the connected load by appliance type. Listing only convertible appliances keeps the application accurate.
4. Pull the permit
The permit goes through LADBS (PermitLA or ePlanLA) in the city or through County Building and Safety in unincorporated areas. Pay the fees and keep the permit number with the job.
5. Do the work
The licensed technician installs or converts the equipment, adjusts or replaces orifices and regulators as needed, and pressure tests new piping before it is concealed behind walls or flooring.
6. Pass the local inspection
The inspector verifies the work and releases the piping to the gas company. In the county, remember the 12-month window to request the first inspection.
7. Pass the SoCalGas requirements
SoCalGas states that local and state ordinances require appropriate permits and final inspections before it establishes service, and that it will not establish service until the piping is released by the local inspection agency and its safety requirements are met. Even after release, its own inspection may add safety-based requirements that go beyond local or state code. Build a little time into your schedule for this last layer, especially if you need gas back on for a cold snap or a move-in date.
Common mistakes that delay conversions
- Applying in the wrong jurisdiction. An address that reads “Los Angeles” may be in the county or a separate city.
- Listing appliances that cannot convert. This forces a revised service application.
- Skipping the BTU totals. Without connected load by equipment type, the application is incomplete.
- Concealing piping before the pressure test. Inspectors need to see the piping tested before it is closed up.
- Treating the permit as final approval. The permit only requests inspection. The job is finished when it passes.
- Letting the county inspection window lapse. The 12-month request period and 180-day follow-ups are easy to miss on long projects.
Our perspective on gas conversions
We convert gas appliances from LP to natural gas across Orange County and Los Angeles County, and our experienced, licensed technicians treat the permit and inspection as part of the job, not an afterthought. A conversion is a safety project first. The right orifice, the right regulator setting and a leak-tight connection matter more than how quickly the appliance lights.
Homeowners and property managers tend to get the best result when they plan the conversion before the appliance arrives, not after. Knowing the appliance’s load, whether it is convertible and which agency covers the address turns a stressful turn-on into a predictable one.
Our approach is built on clear, upfront pricing, warranty-safe solutions and responsive local service. If you want to understand the economics before you commit, our guide on whether converting LP to natural gas is worth it walks through the decision.
MDTECH
Book a licensed technician for your conversion
MDTech Services provides gas appliance conversions from LP to natural gas, gas appliance repairs and appliance installation for homeowners, landlords and property managers in Orange County and Los Angeles County. You can describe your project and book an appointment online through our main site, or look at our gas appliance repair service if an existing gas appliance needs attention first.
For dryers specifically, our 12-step propane dryer conversion guide shows what a safe conversion involves, and our gas to natural conversion guide for homeowners covers the whole-home picture. After the work is done, a gas line inspection is a good way to confirm everything is safe and compliant.
FAQ
Do I need a permit to convert just one appliance, like a dryer?
The California Building Code requires a permit before converting a gas system it regulates, and exempts only portable heating appliances and minor part replacements that do not change the equipment’s approval. A conversion that changes the fuel the appliance burns, or that alters gas piping, generally falls on the permit side. Confirm with LADBS or County Building and Safety for your address, and have a licensed technician do the work.
How much does a gas permit cost in LA County?
In unincorporated LA County, the schedule effective July 1, 2026 lists a $41.35 base plumbing permit and $24.47 for a low-pressure gas system of five outlets or fewer. That totals $65.82 before extras such as additional outlets at $6.20 each. City of Los Angeles fees are set separately by LADBS.
Can the gas company turn on service before the inspection?
No. SoCalGas says it will not establish natural gas service until the piping is released by the local inspection agency and its safety requirements are met. Plan your inspection date before your move-in or appliance delivery date.
Can I pull the permit myself as the homeowner?
In some cases, yes. LA County allows permits to be issued to owners in certain cases, and LADBS lets homeowners apply for single-family e-permits. Gas work is still licensed trade work with inspection requirements, so most owners hire a licensed technician rather than take on the safety responsibility.
Does a landlord need a permit for a tenant-occupied unit?
The same permit rules apply to rental properties. The owner or property manager is the one who authorizes the work, so renters cannot approve a conversion on their own.
Sources
- 105 Permits, 2025 California Building Code
- Los Angeles County Plumbing Code, Title 28, Section 103.0 Permits
- About the Construction Process, LADBS
- LADBS home page
- Homeowner step by step, LADBS
- Los Angeles County Building and Safety permits
- Los Angeles Municipal Code, Section 93.0202 and related sections
- SoCalGas Natural Gas Service guidebook, December 2024 (LADBS copy)
- SoCalGas Gas Service Guidebook
- LA County plumbing code fees, 2026-2027
- LA County plumbing code fees, 2025-2026
- Preparing a gas dryer for a move


